Manuals

downloadUser Manual Chiller JL-6000  Click here

Features :

1. Dual digital tube display, set the temperature and real-time temperature at a glance.
2. Full power refrigeration, micro-cooling, heating control (plus configuration), suitable for various working conditions.
3. Intelligent and constant working mode, suitable for various ambient temperatures.
4. High precision temperature control, volatility can be controlled within 0.5 °C.
5. With temperature overtemperature alarm, sensor fault self-diagnosis function.
6. Have the compressor over the load protection, water flow alarm function.
7. It has anti-freeze function and can better protect machine waterway components in the low temperature environment in the North.

feature :

1. Digital display, can quickly set the temperature and real-time temperature.
2. Full cooling, with heat control cooling, suitable for various working conditions.
3. Intelligent and constant working mode suitable for different temperatures
4. High precision temperature control, fluctuation can be controlled within 0.5 °C.
5. If the temperature is abnormal, the sensor will self-diagnose the fault.
6. More compressors than load, water flow alarm function
7. It has anti-freeze function and can protect the components of the water machine in low temperature environment.

Maintenance matters :

1. Weekly or HALF-MONTHLY cleaning of dust screen or filter dirt intake, in order to avoid causing high temperature alarm of water chillers and other malfunctions.
2. Regularly disassemble the side panels of the machine and clean the dust and dirt attached to the condenser (radiator) with a high-pressure air gun.
3. Replace the circulating water every two months and remove and clean the filters installed so as not to cause dirty water blockage and water flow alarm.
4. Regular inspection of water joint pipe leakage, electrical wiring fixing screw loosening, to prevent poor circuit contact.
5. Every 15-30 days, the filters need to be cleaned to clean and dust.

Maintenance :

1. Clean the dust screen or dirt filter every 14 days to avoid high temperature of the cooling tank and other internal devices.
2. Regularly remove the side panel of the machine and clean the dust and dirt stuck to the condenser (radiator) with a high-pressure air gun.
3. Change the circulating water every 2 months. Change and clean the installed filter to prevent clogging of dirty water and prevent the tank flow warning signal.
4. Regularly check the water pipe for leaks. Loosen the screws holding the wires to prevent bad contact with the circuit.
5. Every 15-30 days, the filter must be removed for cleaning and dust removal.

Temperature controller :

Temperature controller :

Matters needing attention :

1. The equipment must be far away from fire source, heating body and electronic components with strong interference electromagnetic wave.
2. Equipment is prohibited from carrying liquid transportation, so as not to damage internal components.
3. The inlet and outlet of equipment should be more than 50cm away from obstacles, so as to avoid high temperature alarm failure.
4. The equipment should not be inverted or inclined to more than 45 degrees, so as not to damage parts.
5. The equipment must be placed horizontally, and the lock wheel must be well fixed.
6. It is forbidden to start the machine without water, so as not to damage internal components.
7. The length of the external waterway should not be too long, so as not to alarm the malfunction of the waterway, specifically refer to the pump head flow requirements.

Matters of interest :

1. The device must be kept away from fire sources, heaters and electronic components that generate strong electromagnetic interference.
2. Always drain water from the unit before transport to avoid damaging internal components.
3. The inlet and outlet of the equipment should be more than 50cm away from obstacles to avoid failure of high temperature alarm.
4. The machine should not be turned upside down or tilted more than 45 degrees to avoid damaging the parts.
5. The equipment must be placed horizontally and the wheels must be locked to keep the machine in place.
6. Do not turn on the device while there is no water to avoid damaging the internal components.
7. The length of the external water passage should not be too long, so as not to cause abnormal water passage (refer to the pump head flow requirements).

Prompt Message :

1. Capacity of water tank: 12L
2. First adds water to it, then connects the water pipe, so as to remove the internal air and prevent the self-protection of the pump.
3. The circulating water should be distilled water and purified water.
4. When the water level is too low, the machine must be supplemented.
5. Under extremely cold temperatures, a volume ratio of less than 20% ethanol or non corrosive antifreeze should be appropriately added.
6. It is forbidden to add antifreeze fluid, water tank, and corrosive liquid to copper and stainless steel.

Notification message :

1. Water tank capacity (Capacity of water tank): 12L
2. First fill it with water and then connect the water pipe to remove the air inside and prevent the pump from protecting itself.
3. Circulating water should be distilled water and purified water.
4. When the water level is too low, add more water immediately.
5. Under cold temperatures, the volume ratio of ethanol less than 20% or a suitable non-corrosive antifreeze should be added.
6. Do not add antifreeze, water tank antifreeze, or corrosive liquids to copper and stainless steel.

How to set the Chiller temperature JL-6000 :

1.Before setting up, the machine is in the compressor state and the pump is running. (Is the set old temperature)

2. Press the setting button > adjust the temperature as desired, with ↑ increases the temperature value and ↓ decreases the temperature value > setting button again.
3. The temperature will gradually adjust down when the set temperature is reached. The machine will notify the status of the increase in the Bypass valve and Compressor stops working.

How to set the machine temperature Chiller JL-6000 :

1. Before setting, the machine is in Compressor and Pump working state (the old set temperature).
2. Give a button Set up > Adjust the temperature as desired by increasing the temperature and decreasing the temperature > Press the button. Set up   Once again
3. The temperature will gradually decrease. When the set temperature is reached, the machine will indicate the Bypass valve status and the Compressor will stop working.

Temperature adjustment procedure for Chiller model CW/JL6000